LEAD MPEG-2 Encoder (3.0)

The LEAD MPEG-2 Encoder Filter is a DirectShow® filter for compressing video data using the MPEG-2 (ISO/IEC 13818-2) or MPEG-1 (ISO 11172-2) standard. The LEAD MPEG-2 Decoder is a DirectShow® filter for decompressing MPEG-2 video data.

MPEG-1 is the older standard and achieves higher compression than MPEG-2 (but at lower quality). MPEG-1 compression is used in VCD (video on CD).

MPEG-2 is the newer standard and has lower compression than MPEG-1 but the quality is much better than MPEG-1. MPEG-2 is a high quality video compression algorithm and is best suited for applications with higher bit rates or high-bandwidth usage. The most common applications include DVD-Videos, SVCD and digital TVs. The compressed video data can be stored inside MPEG, AVI, DICOM or Ogg files with the option of saving the file with or without the audio data.

The DICOM files can store MPEG-2 SD or HD video. See "Supplement 42: MPEG2 Transfer Syntax" and "Supplement 137: MPEG2 MP@HL Transfer Syntax" of the DICOM specification for more information on requirements of the MPEG-2 SD or HD video.

The compression options for the LEAD MPEG-2 Encoder can be set manually through the encoder property page. The compression options can also be set programmatically using the ILMMPEG2Encoder interface.

The maximum video size for MPEG2 video is 1920x1152 (when using the High profile).

Component Description
Filter Interfaces ILMMPEG2Encoder, ILMMCommon
Interface ID IID_ILMMPEG2Encoder
Input Media Types Type:
MEDIATYPE_Video
Subtypes:
MEDIASUBTYPE_YV12
MEDIASUBTYPE_YUY2
MEDIASUBTYPE_UYVY
MEDIASUBTYPE_RGB32
MEDIASUBTYPE_RGB24
Output Media Types Type:
MEDIATYPE_Video
Subtype:
MEDIASUBTYPE_MPEG2_VIDEO
MEDIASUBTYPE_LMPG2
Filter CLSID CLSID_LMMPEG2Encoder
Property Page CLSID CLSID_LMMPEG2EncoderProperty
Executable LEncMpg23.dll (Win32) / LEncMpg23x.dll (x64), DSKernel2.dll
Filter Category CLSID_VideoCompressorCategory
Header ILEncMPEG2_3.h

Comments

Levels and Profiles

A MPEG-2 encoder capable of handling all resolutions, bit rates and frame rates up to HDTV would be too expensive for many simpler applications or hardware implementations. Therefore, the MPEG-2 standard was subdivided into levels and profiles. The MPEG-2 standard allows for four source formats, or Levels, to be coded; ranging from Limited Definition (todays VCR quality), to full HDTV, each with a range of bit rates. In addition to this flexibility in source formats, MPEG-2 allows for different Profiles. Each profile offers a collection of compression tools that together make up the coding system. A different profile means that a different set of compression tools is available. The four levels, including frame size and maximum bit rate, are defined in the following table:

Level Maximum Frame size (PAL/NTSC) Maximum Bitrate Significance
Low 352x288352x240 4 Mb/s CIF, consumer tape equiv.
Main 720x576720x480 15 Mb/s ITU-R 601, Studio TV
High 1440 1440x11521440x1080 60 Mb/s 4x 601, consumer HDTV
High 1920x11521920x1080 80 Mb/s PROD. SMPTE

Most of today's work is done at the Main Level, which is designated for standard video. Within this level, the Main profile is used for many applications. The MPEG-2 encoder will automatically adjust the level if the video being encoded is bigger than the maximum size for the current level.

I Frames and P Frames

To increase the compression performance, MPEG-2 uses Temporal Compression. Temporal compression is achieved by encoding only the difference between successive frames instead of the frames themselves. This means that frames cannot be considered in isolation. A given picture is constructed from the prediction from a previous picture, and may be used to predict the next picture. An MPEG-2 video stream is comprised of I Frames, B Frames and P Frames:

To increase the compression of MPEG-2, more B and P frames should be used. You do so by adjusting the "I Frame" and "P Frame" options on the Encoder property page:

For example if I frame is 12, and P Frame is 3, then video stream looks like the following:

I B B P B B P B B P B B I B B P B B P B B P B B ..

The distance between I frames must be a multiple of the distance between the P frames. The LEAD MPEG-2 Encoder will automatically adjust these values to preserve this relationship.

This filter is included as part of LEAD MPEG-2 Video Codec Module.

Platforms

Win32, x64.

See Also

LEAD MPEG-2 Encoder User Interface

Help Version 23.0.2024.9.29
Products | Support | Contact Us | Intellectual Property Notices
© 1991-2024 LEAD Technologies, Inc. All Rights Reserved.

LEADTOOLS Filters C API Help
Products | Support | Contact Us | Intellectual Property Notices
© 1991-2023 LEAD Technologies, Inc. All Rights Reserved.